Miele KWT 6112 iG ed/cs Operating And Installation Instructions Download Page 23

Page: 23 / 64

Selecting further settings

Display brightness



The display brightness can be adjusted
to suit lighting conditions in the room.

The display brightness can be adjusted
in steps from

. The factory default

setting is

(maximum brightness).

Altering the display brightness



Touch the settings sensor.

All symbols available for selection will
appear in the display and the



sym-

bol flashes.



Touch the sensors for setting the
temperature (





) repeatedly until

the



symbol flashes.



Touch the OK sensor to confirm your
selection.

The last selected setting flashes and
the



symbol lights up in the display.



By touching the





sensor you

can now alter the brightness of the
display:

: dimmest setting

: medium setting

: brightest setting.



Touch the OK sensor to confirm your
selection.

The selected setting is applied, the



symbol flashes.



Touch the settings sensor to leave
settings mode.
Otherwise the appliance exits set-
tings mode automatically after ap-
proximately one minute.

Summary of Contents for KWT 6112 iG ed/cs

































































Search results

Summary of Contents for KWT 6112 iG ed/cs

Reviews:

Related manuals for KWT 6112 iG ed/cs

Brands by name

Popular brands

Miele KWT 6112 iG ed/cs, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6112 iG ed/cs

Reviews:

Related manuals for KWT 6112 iG ed/cs

Brands by name

Popular brands