Miele KWT 6112 iG ed/cs Operating And Installation Instructions Download Page 61

Page: 61 / 64

Installing the wine conditioning unit



Secure the wine conditioning unit to
the carcase using the four screws
supplied (4 x 29)



. The screws

should be screwed into the carcase
at a slight angle (approx. 15°).



Fit the covers



(supplied).



Now connect the wine conditioning
unit to the electrical supply.

When the wine conditioning unit is con-
nected to the electrical supply, the
mains connection symbol



will ap-

pear in the display after a short while.



Touch the On/Off button.

The mains connection symbol



will

go out and the wine conditioning unit
will start to cool.

The Push2open system on the wine
conditioning unit is now activated (see
"Guide to the appliance – Door opening
mechanism").

Summary of Contents for KWT 6112 iG ed/cs

































































Search results

Summary of Contents for KWT 6112 iG ed/cs

Reviews:

Related manuals for KWT 6112 iG ed/cs

Brands by name

Popular brands

Miele KWT 6112 iG ed/cs, Operating And Installation Instructions

Search results

Summary of Contents for KWT 6112 iG ed/cs

Reviews:

Related manuals for KWT 6112 iG ed/cs

Brands by name

Popular brands