Miele FM3 Operating Instructions Manual Download

Page: 28 / 80

Switching on the appliance

Filling the water container

If the water container is empty or not
installed in the tower, the message



Insert or refill the water container

displayed.

Removing the water container



Hold the water container by its han-
dle.



Pull the handle down.

The water container is released from the
retainer.



Pull the water container upwards and
out.

You may notice some water dripping
when removing the water container
while the water container valves are
closing.

Tip:

The dripping can be prevented by

removing the water container slowly.

Filling the water container



Open the twist lock at the rear of the
water container by turning the lock
counterclockwise.



Remove the twist lock.



Use fresh tap water to fill the con-
tainer (water temperature approx.
60 to 95°F / 15 to 35°C).

Tip:

When placing the water container

in the horizontal position, the water
container can also be filled if the faucet
is installed very low.



Replace the twist lock in the opening
of the water container.



Close the twist lock by turning it
clockwise as far as it will go.



Put the water container back into the
tower.

The water container can be removed
and refilled at any time (even during
the ironing process). The amount of
water required will depend on how
much steam is required.

Summary of Contents for FM3

















































































Search results

Summary of Contents for FM3

Reviews:

Related manuals for FM3

Brands by name

Popular brands

Miele FM3, Operating Instructions Manual

Search results

Summary of Contents for FM3

Reviews:

Related manuals for FM3

Brands by name

Popular brands