Miele DA 6590 W Operating Instructions Manual Download Page 82

Page: 82 / 96

Frequently Asked Questions

Problem

Possible cause and solution

White residue is visible

on dishware and cut‐

lery, clouding occurs on

glassware; this film can

be wiped off.

The rinse aid dosage is too low.



Increase the dosage (see "Settings menu - Rinse

aid").

The salt reservoir is empty.



Fill the salt reservoir (see "Before using for the first

time - Dishwasher salt").

The salt reservoir cap has not been screwed on cor‐

rectly.



Replace it, making sure that it screws back on

correctly.

An unsuitable Tab detergent has been used.



Change your detergent.

The water softener is programmed to too low a water

hardness level.



Program the water softener to a higher water hard‐

ness level (see "Settings menu - Water hardness").

There are rust stains on

the cutlery.

The affected items are not corrosion resistant.



There is no remedy.

Purchase cutlery which is dishwasher-safe.

A program was not run after dishwasher salt was

added. Traces of salt have got into the wash cycle.



Always run the

Express

program with the

Short

program option selected and without any dishware

in the dishwasher after adding dishwasher salt.

The salt reservoir cap has not been screwed on cor‐

rectly.



Replace it, making sure that it screws back on

correctly.

Summary of Contents for DA 6590 W

































































































Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands

Miele DA 6590 W, Operating Instructions Manual

Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands