Miele DA 6590 W Operating Instructions Manual Download Page 60

Page: 60 / 96

Settings menu

Setting the electricity rate times

Before you can use the

EcoStart

option,

you must set at least one electricity rate

time.



Use the



arrow buttons to select

the electricity rate time (R1-R3) you

want to set and confirm with

The start of the electricity rate time se‐

lected will appear in the display and the

hour number block will be highlighted.



Use the



arrow buttons to set the

hours and minutes for the start time

and confirm both with

The end of the electricity rate time se‐

lected will appear in the display and the

hours number block will be highlighted.



Use the



arrow buttons to set the

hours and minutes for the end time

and confirm both with

The electricity rate time will be saved

and its priority will appear in the dis‐

play.



Use the



arrow buttons to set the

priority you want and confirm with



Confirm the message with

The electricity rate time will be activat‐

ed.

Changing the electricity rate times

You can change the start, finish or pri‐

ority of an electricity rate time.



Use the



arrow buttons to select

the electricity rate time (R1-R3) you

want to change and confirm with



Select the setting you want to change

and confirm with



Use the



arrow buttons to change

the setting and confirm with



Confirm the message with

The change will be saved.

Summary of Contents for DA 6590 W

































































































Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands

Miele DA 6590 W, Operating Instructions Manual

Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands