Miele DA 6590 W Operating Instructions Manual Download Page 71

Page: 71 / 96

Frequently Asked Questions

With the help of the following guide, minor faults in the performance of the appli‐

ance, some of which may result from incorrect operation, can be put right without

contacting Miele Service. This will save time and money.
The following guide may help you to find the reason for a fault, and to correct it.

You should, however, note the following:



Unauthorized or incorrect repairs could cause personal injury or damage to

the appliance.
Repair work to electrical appliances must only be carried out by a suitably

qualified and competent person in strict accordance with current local and na‐

tional safety regulations. The manufacturer cannot be held liable for unauthor‐

ized work.

Technical problems

Problem

Possible cause and solution

The dishwasher does

not start.

The door is not properly closed.



Raise the door upwards until the catch engages.

The dishwasher is not plugged in.



Insert the plug.

The circuit breaker has tripped.



Reset the fuse (see data plate for the correct fuse

rating).

The dishwasher is not switched on.



Turn the dishwasher on with the



button.

The dishwasher stops

during a program.

The circuit breaker has tripped.



Reset the fuse (see data plate for the correct fuse

rating).



If the circuit breaker trips again, contact Miele

Service.

After the program has

started, the Optical In‐

terface is not visible.

The indicator reflector panel was not correctly fitted.



Refit the indicator reflector panel correctly (see the

installation plan).

Summary of Contents for DA 6590 W

































































































Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands

Miele DA 6590 W, Operating Instructions Manual

Search results

Summary of Contents for DA 6590 W

Reviews:

Related manuals for DA 6590 W

Brands by name

Popular brands