Middle Atlantic Products C3 1-bay Instruction Sheet Download Page 8

Page: 8 / 38

SUPPLIED COMPONENTS AND HARDWARE (CONTINUED)

Page 8

NOTE

• Images in this instruction sheet may show 1-, 2-, or 4-bay models.

• Hardware amounts for custom credenzas may vary.

• Additional hardware is included that may not be required for your installation.

MAGNETIC KEY DOOR LOCK OPTION (MAG-CAB-LATCHKEY)

REQUIRED TOOLS

• Protective Eyewear

• Tape Measure

• Pencil

• Level

• Stud Finder

• Power Driver

• 3/32” Drill Bit (For Wood Studs)

• ½” Drill Bit (For Steel Studs, Cinderblocks, or Masonry)

• 7/16” Socket and Wrench

• Rubber Mallet

• #2 Phillips Screwdriver

• #2 Phillips Bit

• 1½” Hole Saw With Drill Bit Tip

WARNING:

Use tools with caution and follow all necessary safety protocols.

AVERTISSEMENT:

Utiliser des outils avec prudence et suivre tous les protocoles de sécurité

nécessaires.

FAN OPTION (C3-FANKIT)

Fan Controller

Fan

(5x)

#10 x 5/8” Fan

Mounting Screw

(3x)

#6 x 3/8” Fan

Controller Mounting

Screw

(12x)

Wire Tie

Global Fan Controller Power Supply

(With US, AU, BS, and SAA Attachments)

Plunger

Magnetic Door Latch

(4x) #8 x ½” Wood

Screw

(2x) Magnetic Key

AAA

Door Catch

Summary of Contents for C3 1-bay







































Search results

Summary of Contents for C3 1-bay

Reviews:

Related manuals for C3 1-bay

Brands by name

Popular brands

Middle Atlantic Products C3 1-bay, Instruction Sheet

Search results

Summary of Contents for C3 1-bay

Reviews:

Related manuals for C3 1-bay

Brands by name

Popular brands