![Microcom 438TM Operator'S Manual Download Page 113](http://html1.mh-extra.com/html/microcom/438tm/438tm_operators-manual_1786158113.webp)
Chapter 5
Printer Commands
438TM Operator’s Manual - 880049-0113 5-45
5.9.4
Cutter Hold-off
This command is used to avoid cutting “air” or the leading edge of the first label when
printing and cutting without advancing the label stock. This command is used with the Full
or Partial Cut Mode (^D99), but not the Kiosk Cut Mode. This function will skip a pre-set
number of cuts following a Top of Form. Count resets and begins count at TOF or following
the point where the command is given.
Note: Advance distance must be set at “0” for this command to function.
XX
117
Cutter Hold-off:
X represents the number of cuts to skip on the first X labels
following a Top of Form.
5.10 Dispensing Commands
Dispensing commands are commands that advance the media for cutting, tear off, or
presenting and then retract the media to a home position so that media is not wasted.
These dispense commands include Peel-n-Dispense, Tag/Tear, Cutter commands, and
optional media handling commands as well. The following commands define these types of
operations. Most of the dispensing commands require that the printer is configured with an
optional Label Present Detector.
5.10.1 Tag/Tear Operation
This command controls a method of dispensing the media so that the perforation between
labels is positioned on the tear bar or peel edge. Once the label is taken, the label media
retracts and allows proper registration of the next label print. Once the label is taken, the
label media retracts and allows proper registration of the next label print.
^A
^D
COMMAND
X
97
Tag/Tear Operation:
0
Disable Tag/Tear operation.
1
Advance after every print.
2
Advance after copies count.
3
Advance when idle. (Does not use LPD - retracts stock at next sent label
format.)
5.10.2 Peel-and-Dispense Operation
This command is used when the labels are to be peeled from the backing material. Once
the label is taken, the label media retracts and allows proper registration of the next label
print. This command requires that the printer is configured with the optional label peel
assembly for proper operation. Not all models support the label peel option.
X
98
Peel-and-Dispense Operation:
0
Disable Peel-and-Dispense operation.
1
Enable Peel-and-Dispense operation.
5.10.3 Load Advance/Retract Distance and Load Advance Delay
XX
95
Advance/Retract Distance:
This command is used in conjunction with the
tag/tear (^D97), peel-n-dispense (^D98), and cutter (^D99) commands. It is
used to adjust the number of steps the printer will advance the media after
Summary of Contents for 438TM
