manualshive.com logo in svg

Meritor MTC-4208X Series, Service Manual, Page: 92 / 120

Share
Download
Meritor MTC-4208X Series Service Manual Download Page 92

Copyright Meritor, Inc., 2020

MM-0861 / Revised July 2020
Page 88

Printed in USA

8

     Installation

Installation

Hazard Alert Messages

Read and observe all Warning and Caution hazard alert messages in 
this publication. They provide information that can help prevent serious 
personal injury, damage to components, or both.

 

WARNINGS

TO PREVENT EYE INJURY, ALWAYS WEAR EYE PROTECTION 
WHEN PERFORMING VEHICLE MAINTENANCE OR SERVICE.

Install the Transfer Case

 

DANGER

SUPPORT THE TRANSFER CASE WITH A LIFTING DEVICE 
BEFORE MOVING THE TRANSFER CASE. A TRANSFER CASE 
THAT IS NOT SUPPORTED CORRECTLY CAN FALL. SERIOUS 
PERSONAL INJURY AND DAMAGE TO COMPONENTS CAN 
RESULT.

1.  Use a suitable lifting device to move the transfer case from the 

repair stand to a suitable hydraulic roller jack. If used, remove 
the temporary eye-bolts and mounting brackets from the transfer 
case housing.

2.  Move the transfer case into position under the vehicle with the 

hydraulic roller jack.

3.  Install the transfer case into the vehicle with the mounting bolts. 

Tighten the bolts to the torque specifi cation supplied by the 
vehicle manufacturer.

4.  Connect the drivelines to the input and output yokes of the 

transfer case. Refer to the vehicle manufacturer’s recommended 
procedure.

5.  Connect any switch or speed sensor wiring. 

6.  Fill the transfer case with the correct quantity of specifi ed 

lubricant. Refer to “Lubrication & Maintenance” on page 97.

Oil Cooler Line Connections

MTC-4213, or MTC-4208 & MTC-4210 with Oil Cooler

NOTE:

 There are different transfer case lubrication systems available. 

Determine the transfer case model before ordering cooler adaptation 
ports.

MTC-4213 or MTC-4208 & MTC-4210 Models with 
PTO

Figure 8.1

MTC-4213X, MTC-4208X/XP, & MTC-4210X/XP

4007120a

OUTLET TO 
OIL COOLER

DRAIN
PLUG

FRONT

LOOP LINE USED 
FOR NON-OIL 
COOLER 
OPERATION 
ONLY

INLET FROM

OIL COOLER

1.  Disconnect the loop line on top of the transfer case connecting 

the pump exit and return ports on the transfer case. Figure 8.1 
and Figure 8.2.

2.  Install the cooler inlet and outlet lines.

Summary of Contents for MTC-4208X Series

























































































































Reviews:

No comments