Meritor MTC-4208X Series Service Manual Download Page 50

Page: 50 / 120

MM-0861 / Revised July 2020
Page 46

Printed in USA

Disassembly

MTC-4213X only:

The rear output shaft and high-range gear are

removed as an assembly along with the rear cover. The shaft is
pressed into the bearing assembly which keeps the shaft retained
in the housing. Refer to the “Disassemble MTC-4213X Rear
Output Shaft Assembly” on page 47.

MTC-4208X/XP/XL/XLEV & MTC-4210X/XP/XL/XLEV only:

Remove the high range helical gear.

8. Remove the high and low shift fork, shift shaft, and clutch collar

from the front case. Figure 4.22.

Figure 4.22

4000194c

HIGH AND LOW
SHIFT FORK &
SHAFT ASSEMBLY

DOUBLE-GEAR

IDLER SHAFT

9. Remove the single-gear idler shaft on MTC-4213X, or rear output

on MTC-4208X/XP/XL/XLEV & MTC-4210X/XP/XL/ XLEV, and the
double-gear idler shaft from the case. Figure 4.23.

Figure 4.23

4000195a

10. Remove the front output shaft, clutch collar, shift fork, and spring

as an assembly.

11. Remove the shift cylinder and push rod from the front case.

12. Remove the two locating dowel pins. Note their correct location.

Disassemble the Front Output Shaft Assembly

1. Temporarily install the yoke and nut. Secure the yoke to prevent

the shaft from rotating when removing the rear nut. Support the
shaft correctly.

2. Remove the rear nut and washer.

3. Remove the yoke.

4. Prepare the shaft for bearing and gear removal. Install the front

output shaft into a press with the rear of the output shaft facing
UP. Support the shaft correctly. Figure 4.24.

Figure 4.24

PRESS

SHAFT

BLOCK

4007098b

5. Press the shaft DOWNWARD to remove the rear tapered roller

bearing, helical gear, clutch collar, and needle bearing from the
assembly.

6. Install a bearing separator or other suitable tool below the forward

roller bearing. Figure 4.25.

Figure 4.25

PRESS

SHAFT

BEARING

SEPARATOR

BLOCK

4007099b

7. Install the output shaft assembly into a press and support it

correctly. Figure 4.25.

8. Press the output shaft DOWNWARD to remove the front roller

bearing.

Summary of Contents for MTC-4208X Series
























































































































Search results

Summary of Contents for MTC-4208X Series

Reviews:

Meritor MTC-4208X Series, Service Manual, Page: 50 / 120

Search results

Summary of Contents for MTC-4208X Series

Reviews: