manualshive.com logo in svg

Meritor MTC-4208X Series, Service Manual, Page: 88 / 120

Share
Download
Meritor MTC-4208X Series Service Manual Download Page 88

Copyright Meritor, Inc., 2020

MM-0861 / Revised July 2020
Page 84

Printed in USA

7

     Power Takeoff (PTO)

Install the PTO Onto the Transfer Case

1.  Install two dowel pins into the transfer case PTO fl ange.

2.  Apply a thin coating of Loctite 518 gasket sealant to the entire 

PTO fl ange mounting surface. Figure 7.2.

3.  Slide the PTO assembly onto the output shaft spline. Align the 

assembly to the two dowel pins.

4.  Install the washers and mounting bolts. Tighten the bolts to 60-75 

lb-ft (81-102 N∙m). 

5.  Install the PTO air control line and fi tting. Follow the vehicle 

manufacturer’s instructions.

Test the PTO Installation

 

CAUTION

THE PTO CLUTCH MUST BE ENGAGED TO OPERATE THE 
DRIVE. ALWAYS ENGAGE AND DISENGAGE THE PTO WITH 
THE VEHICLE STATIONARY AND IN NEUTRAL. NEVER APPLY 
A LOAD TO THE PTO DRIVE UNTIL THE DRIVE HAS BEEN 
ENGAGED. DAMAGE TO COMPONENTS CAN RESULT.

THE AIR PRESSURE MUST NOT EXCEED 90 PSI (6.2 BAR). 
DAMAGE TO COMPONENTS CAN RESULT.

1.  Connect a regulated air pressure line to the air control port. Figure 

7.6.

Figure 7.6

4000217a

AIR

CONTROL

PORT

PTO
ASSEMBLY

PTO SWITCH
(OPTIONAL)

2.  Apply 90 psi (6.2 bar) of air pressure.

3.  Check for leaks in the PTO air control line.

4.  Cycle the air control pressure. Follow the procedures below to 

verify the PTO clutch engages correctly.

PTO Without an Optional Indicator Switch

1.  Remove the switch port screw and washer. Figure 7.4.

2.  Measure the PTO push rod travel to verify the travel is 0.75” (19 

mm) and the clutch is fully engaged.

If the push rod travel is not at 0.75” (19 mm) and the PTO 
clutch is not fully engaged:

 

Disengage the clutch by releasing the air pressure. Rotate the 
clutch output shaft by hand and retest.

If the clutch still is not fully engaged:

 

Remove the PTO assembly. Check the transfer case output 
shaft splines and the PTO clutch collar splines. Replace worn or 
damaged parts. Repeat the assembly procedures.

PTO with an Optional Indicator Switch

1.  Install the indicator switch. Tighten the switch to 25-30 lb-ft 

(34-40.8 N∙m). 

2.  Verify the indicator switch closes when the PTO completes a shift 

to engage the drive. Figure 7.5.

If the indicator switch does not close to fully engage the 
drive:

 

Measure the PTO push rod travel to verify the travel is 0.75” (19 
mm) and the clutch is fully engaged.

If the push rod travel is not at 0.75” (19 mm) and the PTO 
clutch is not fully engaged:

 

Disengage the clutch by releasing the air pressure. Rotate the 
clutch output shaft by hand and retest.

If the clutch still is not fully engaged:

 

Remove the PTO assembly. Check the transfer case output 
shaft splines and the PTO clutch collar splines. Replace worn or 
damaged parts. Repeat the assembly procedures.

Summary of Contents for MTC-4208X Series

























































































































Reviews:

No comments