Mercury SMARTCRAFT Operation Manual Download Page 14

Page: 14 / 96

MONIT

OR 1.01-1.02

1-8

MONITOR – VERSION 1.01-1.02

Warning Display Screens

IMPORTANT: Refer to the Engine Operation, Maintenance
Manual for further explanation of the problem and the correct
action to take.

Oil Pump Fault

The Bell, Engine and oil icons
are displayed. The oil pump has
stopped functioning electrically.
No lubricating oil is being sup-
plied to the engine.

Water in Fuel

The Bell and Fuel Icon are dis-
played. Water in the water-sep-
arating fuel filter reached the full
level.

Engine Overspeed

The Bell icon is displayed. The
engine speed exceeded the
maximum allowable RPM.

Engine Malfunction

The Bell and Engine Icon will
appear to inform the driver that
an engine problem occurred.

Summary of Contents for SMARTCRAFT

































































































Search results

Summary of Contents for SMARTCRAFT

Reviews:

Related manuals for SMARTCRAFT

Brands by name

Popular brands

Mercury SMARTCRAFT, Operation Manual

Search results

Summary of Contents for SMARTCRAFT

Reviews:

Related manuals for SMARTCRAFT

Brands by name

Popular brands