Mercury SMARTCRAFT Operation Manual Download Page 47 | Manualshive

Page: 47 / 96

background image

MONIT

OR 2.00

2-21

MONITOR – VERSION 2.00

CAL 2 Calibration

Tank 2 Calibration

Select whether you want to cali-
brate tank 2.
NOTE: Tank 2 does not have to
be a fuel tank. It could represent
an oil tank for example.
NOTE: The gauge will not let you
calibrate the tank until the capac-
ity had been entered).

1. Press the

button until “t2” is displayed. “t2” = tank 2.

2. Press the

button to select 1= on, 0 = off. Selecting “1” will

continue tank 2 calibration.

3. Press the

button to continue.

Tank 2 Calibration Icon
Selection

Select one of three icons for
tank 2 display screen. (oil, wa-
ter/waste, fuel).

1. Press the

button, you will see a blinking icon. Using the

button, select which icon you want tank 2 to be, (oil, fuel,

or water/waste).

NOTE:If you choose oil or water/waste icon, no further tank 2 cal-
ibration will be needed. If tank 2 will be for fuel, continue tank 2 pro-
cedure.

2. Press the

button to continue.

Tank 2 Calibration 0%
Setting

Have the fuel tank level at
empty.

3. Press the

button to save. Press the

button to ad-

vance to 25% setting.

«
...
45
46
47
48
49
...
»

Summary of Contents for SMARTCRAFT

































































































Reviews:

No comments

Related manuals for SMARTCRAFT

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: Mach Pages: 12

Brand: UniPix Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands