Mercury SMARTCRAFT Operation Manual Download Page 39

Page: 39 / 96

MONIT

OR 2.00

2-13

MONITOR – VERSION 2.00

CAL 1 Calibration

SAE English System

Metric System

English or Metric

Select whether you want the
readings in the SAE English
system or the Metric system.

1. Press the

button to toggle between units.

2. Press the

button to move to the next function.

Range Readings

Select whether you want the
readings in Miles, Nautical Miles
or Kilometers.

1. Press the

button to toggle between units.

2. Press the

button to move to the next function.

Depth Display (on or
off)

Select whether you want the
depth screen to be displayed.

1. Press the

button to select on or off.

2. Press the

button to move to the next function.

Trim Display (on or off)

Select whether you want the
trim screen to be displayed.

1. Press the

button to select on or off.

2. Press the

button to move to the next function.

Summary of Contents for SMARTCRAFT

































































































Search results

Summary of Contents for SMARTCRAFT

Reviews:

Related manuals for SMARTCRAFT

Brands by name

Popular brands

Mercury SMARTCRAFT, Operation Manual

Search results

Summary of Contents for SMARTCRAFT

Reviews:

Related manuals for SMARTCRAFT

Brands by name

Popular brands