manualshive.com logo in svg

Mercury SMARTCRAFT, Operation Manual

Share
Download
Mercury SMARTCRAFT Operation Manual Download Page 67

SYSTEM 

 T

ACH & SPEED

3-16

SYSTEM TACH & SPEEDOMETER

CAL 1 Tachometer Calibration

TRIM CALIBRATION

[EDIT]

[SKIP]

Choosing edit allows you to calibrate
the gauge to the standard 0–10 unit trim
and 11–25 trailer position scale.

TRIM FULL DOWN THEN

PRESS PLUS BUTTON

[SAVE]

[SKIP]

[DFLT]

TRIM FULL UP THEN

PRESS PLUS BUTTON

[SAVE]

[SKIP]

[DFLT]

TRIM TO TRAILER POINT

THEN PRESS PLUS BUTTON

[SAVE]

[SKIP]

[DFLT]

DISPLAY UNITS

[DOWN]

[UP]

[SAVE]

Lets you change units of measure
between English (standard) or Metric.

SPEED UNITS

[DOWN]

[UP]

[SAVE]

Lets you select speed units. You can
choose from MPH (Miles Per Hour), KN
(Nautical Miles Per Hour) or KMH
(Kilometers Per Hour).

[NO]

[YES]

[SAVE]

DEPTH SCREEN?

Do you want to turn on the depth screen?
(Remember: You must have a Smart
Craft depth transducer connected to the
system for this screen to operate)

ENGINE TEMP SCREEN?

[NO]

[YES]

[SAVE]

Do you want to turn on the engine temp
screen?

(continued on next page)

Summary of Contents for SMARTCRAFT

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands