manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 93

The steering link rod parts are available and assembled as illustrated below.

Spacers may or may not be required depending on cable brands.

a -

Grease

b -

Spacer (optional)

c -

Bolt

d -

Washer B

e -

Rubber cushion

f -

Spring

g -

Spacer

h -

Collar

i -

Locknut

j -

Rod

k -

Washer A

l -

Seal ring

Battery Installation

MOUNTING BATTERY

Follow the battery manufacturer's instructions carefully. Mount battery securely

to the hull in a place free from splashing water.

NOTE: Electric starting outboards must have the battery cables connected to a

battery whenever the engine is running, even if started manually, as damage to

the charging system could result.

a

b

c
d
e

f

a

d

g

h

d

i

j

k

l

d

i

37507

ENGINE INSTALLATION

eng

83

  

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands