manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 71

Spark Plug Inspection and Replacement

!

 WARNING

Damaged spark plug boots may emit sparks that can ignite fuel vapors under

the engine cowl, resulting in serious injury or death from a fire or explosion.

To  avoid  damaging  the  spark  plug  boots,  do  not  use  any  sharp  object  or

metal tool to remove the spark plug boots.

1. Remove the spark plug boots. Twist the rubber boots slightly and pull off.

26899

2. Remove the spark plugs to inspect. Replace spark plug if electrode is

worn or the insulator is rough, cracked, broken, blistered, or fouled.

26946

3. Set the spark plug gap to specification.

26947

Spark Plug
   Spark plug gap

1.0 mm (0.035 in.)

4. Before installing spark plugs, clean off any dirt on the spark plug seats.

Install plugs finger‑tight, and then tighten 1/4 turn or torque to

specifications.

Description

Nm

lb‑in.

lb‑ft

Spark plug

27

–

20

MAINTENANCE

eng

61

  

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands