manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 43

•

Trim up:

 If the bow falls into the water level when cruising, trim the trim

position pin up.

a -

Correct trim

b -

Trim down

c -

Trim up

d -

Trim position pin

e -

Move pin to raise bow up

f -

Move pin to lower bow down

Steering Friction Adjustment

Steering friction can be adjusted according to your preference with the steering

co‑pilot.

!

 WARNING

Insufficient friction adjustment can cause serious injury or death due to loss

of  boat  control.  When  setting  the  friction  adjustment,  maintain  sufficient

steering  friction  to  prevent  the  outboard  from  steering  into  a  full  turn  if  the

tiller handle or steering wheel is released.

Adjust the steering co‑pilot to achieve desired steering friction.

•

Turn clockwise for more friction.

37883

a

b

c

d

e

f

FEATURES AND CONTROLS

eng

33

  

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands