Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 79

Page: 79 / 114

Mercury Marine Validated Engine Mounting Hardware

IMPORTANT: Mercury Marine provides validated fasteners and installation

instructions, including torque specifications, with all of our outboards so they

can be properly secured to boat transoms. Improper installation of the outboard

can cause performance and reliability issues that can lead to safety concerns.

Follow all of the instructions relating to the outboard installation. DO NOT

mount any other accessory onto the boat with the fasteners provided with the

outboard. For example, do not mount tow sport bars or boarding ladders onto

the boat using the mounting hardware included with the outboard. Installing

other products onto the boat that utilize the outboard mounting hardware will

compromise the ability of that hardware to properly and safely secure the

outboard to the transom.
Outboards that require validated mounting hardware will have the following

decal on the transom clamp.

51965

Installing Outboard

We strongly recommend that your dealer install your outboard and related

accessories to ensure proper installation and good performance. If you install

the outboard yourself, follow the instructions in the manual which is provided

with the outboard.

NOTE: Most boats are rated and certified in terms of their maximum

horsepower limit, and this is shown on the boat's certification plate. Do not

equip your boat with an outboard that exceeds this limit. If in doubt, contact

your dealer. Do not operate the engine until it has been securely mounted on

the boat in accordance with the instructions below.

ENGINE INSTALLATION

eng

Summary of Contents for 2.5 TwoStroke



















































































































Search results

Summary of Contents for 2.5 TwoStroke

Reviews:

Brands by name

Popular brands

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Search results

Summary of Contents for 2.5 TwoStroke

Reviews:

Brands by name

Popular brands