manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 77

Starter Motor Will Not Crank the Engine (Electric Start Models)

POSSIBLE CAUSES

•

Remote control models ‑ Blown 20 amp fuse in the starting circuit. Refer

to 

Maintenance

 section.

•

Outboard is not shifted to neutral position.

•

Weak battery or battery connections are loose or corroded.

•

Ignition key switch failure.

•

Wiring or electrical connection faulty.

•

Starter motor or starter solenoid failure.

Engine Will Not Start

POSSIBLE CAUSES

•

Lanyard stop switch not in "RUN" position.

•

Incorrect starting procedure. Refer to 

Operation

 section.

•

Old or contaminated gasoline.

•

Engine flooded. Refer to 

Operation

 section.

•

Fuel is not reaching the engine.

a. Fuel tank is empty.
b. Fuel tank vent not open or restricted.
c. Fuel line is disconnected or kinked.
d. Primer bulb not squeezed.
e. Primer bulb check valve is faulty.
f. Fuel filter is obstructed. Refer to 

Maintenance

 section.

g. Fuel pump failure.
h. Fuel tank filter obstructed.

•

Ignition system component failure.

•

Spark plugs fouled or defective. Refer to 

Maintenance

 section.

Engine Runs Erratically

POSSIBLE CAUSES

•

Spark plugs fouled or defective. Refer to 

Maintenance

 section.

•

Incorrect setup and adjustments.

•

Fuel is being restricted to the engine.

• Engine fuel filter is obstructed. Refer to 

Maintenance

 section.

• Fuel tank filter obstructed.
• Stuck anti‑siphon valve on built in fuel tank.
• Fuel line is kinked or pinched.

•

Fuel pump failure.

TROUBLESHOOTING

eng

67

  

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands