manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 12

Do not overpower or overload your boat. Most boats will carry a required

capacity plate indicating the maximum acceptable power and load as

determined by the manufacturer following certain federal guidelines. If in doubt,

contact your dealer or the boat manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
   CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
   CAPACITY

XXX

26777

High‑Speed and High‑Performance Boat Operation

If your outboard is to be used on a high‑speed or high‑performance boat with

which you are unfamiliar, we recommend that you do not operate it at its high

speed capability without first requesting an initial orientation and familiarization

demonstration ride with your dealer or an operator experienced with your boat/

outboard combination. For additional information, obtain a copy of our

Hi

‑

Performance Boat Operation 

booklet from your dealer, distributor, or

Mercury Marine.

Outboard Remote Control Models

The remote control connected to your outboard must be equipped with a start

in neutral only protection device. This prevents the engine from starting when

the shift is actuated in any position other than neutral.

GENERAL INFORMATION

  

2

eng

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands