manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 74

6. Remove the lubricant tube and install the lower oil plug.

37849

GEARCASE LUBRICANT CAPACITY

Gearcase lubricant capacity is approximately 280 cc (9.5 fl oz).

GEARCASE LUBRICANT RECOMMENDATION

Mercury or Quicksilver Premium or High Performance Gear Lubricant.

Submerged Outboard

A submerged outboard will require service within a few hours by an authorized

dealer once the outboard is recovered from the water. This immediate attention

by a servicing dealer is necessary once the engine is exposed to the

atmosphere to minimize internal corrosion damage to the engine.
Following are the emergency measures to be taken on the submerged

outboard.

1. Immediately take it out of the water and wash it with fresh water to

remove salt or dirt.

2. Remove the spark plugs and completely drain the water from the engine

by pulling the rewind starter several times.

3. Sufficiently inject genuine engine oil through the spark plug hole and into

the crankcase from the carburetor side. Pull the rewind starter several

times to circulate the oil throughout the motor.

MAINTENANCE

  

64

eng

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands