manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 8

Operation

Prestarting Check List.......................................................................................36

Operating in Freezing Temperatures................................................................ 36

Operating in Saltwater or Polluted Water......................................................... 36

Operating at High Elevations............................................................................ 37

Engine Break‑in Procedure...............................................................................37

Starting the Engine........................................................................................... 38

Warm‑Up.......................................................................................................... 44

Gear Shifting..................................................................................................... 44

Stopping the Engine......................................................................................... 47

Emergency Starting.......................................................................................... 48

Maintenance

Cleaning Care Recommendations.................................................................... 50

Inspection and Maintenance Schedule ............................................................ 51

Flushing the Cooling System............................................................................ 52

Top Cowl Removal and Installation.................................................................. 54

Battery Inspection ............................................................................................ 55

Fuel System...................................................................................................... 55

Fuse Replacement ‑ Electric Start Remote Control Models............................. 56

Corrosion Control Anode.................................................................................. 56

Propeller Replacement..................................................................................... 57

Spark Plug Inspection and Replacement..........................................................61

Lubrication Points............................................................................................. 62

Gearcase Lubricant.......................................................................................... 62

Submerged Outboard....................................................................................... 64

Storage

Storage Preparation..........................................................................................65

Protecting External Outboard Components...................................................... 65

Protecting Internal Engine Components........................................................... 66

Gearcase.......................................................................................................... 66

Positioning Outboard for Storage..................................................................... 66

Battery Storage................................................................................................. 66

  

vi

eng

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands