manualshive.com logo in svg

Mercury 2.5 TwoStroke, Operation, Maintenance And Installation Manual

Share
Download
Mercury 2.5 TwoStroke Operation, Maintenance And Installation Manual Download Page 7

General Information

Boater's Responsibilities..................................................................................... 1

Before Operating Your Outboard........................................................................ 1

Boat Horsepower Capacity................................................................................. 1

High‑Speed and High‑Performance Boat Operation.......................................... 2

Outboard Remote Control Models...................................................................... 2

Remote Steering Notice......................................................................................3

Lanyard Stop Switch........................................................................................... 4

Protecting People in the Water........................................................................... 6

Passenger Safety Message ‑ Pontoon Boats and Deck Boats...........................7

Wave and Wake Jumping................................................................................... 8

Impact with Underwater Hazards........................................................................9

Exhaust Emissions........................................................................................... 11

Selecting Accessories for Your Outboard......................................................... 13

Safe Boating Recommendations...................................................................... 13

Recording Serial Number................................................................................. 15

Model Year Production Code............................................................................16

25/30 Specifications..........................................................................................17

Components..................................................................................................... 18

Transporting

Trailering Boat/Outboard.................................................................................. 24

Removing the Motor ........................................................................................ 24

Transporting Portable Fuel Tanks.................................................................... 25

Fuel and Oil

Fuel Requirements........................................................................................... 27

Oil Recommendation........................................................................................ 28

Mixing Fuel and Oil........................................................................................... 28

Filling Fuel Tank............................................................................................... 29

Features and Controls

Remote Control Features................................................................................. 30

Tilting Outboard ............................................................................................... 30

Shallow Water Operation.................................................................................. 31

Trim Adjustment................................................................................................32

Steering Friction Adjustment.............................................................................33

Trim Tab Adjustment........................................................................................ 34

eng

v

  

Summary of Contents for 2.5 TwoStroke



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands