background image

HCP

page 17

Programming example Weekly programmer

Programming example Weekly programmer
The unit has to switch on at 9.30 hrs from Mo to Fr (workday group) and switch off at 19.00 hrs. In 
addition it has to operate on Saturday from 10.00 to 14.00 hrs.

1. Select operating mode “Weekly programmer“

1. Select operating mode “Weekly programmer“
After holding down the SET key (approx. 3 sec) the current operating 
mode is flashing. Select operating mode “Weekly programmer“ with the 
push/turn control while holding down the SET key. After the SET key has 
been released the controller is in operating mode “Weekly programmer“.

PRINT

SETUP

2. Switch on at 9.30 hrs Mo-Fr
Turn the push/turn control anticlockwise to select 

Mo-Fr on

 (workday 

group).
Hold down the SET key and use the push/turn control to set the switch on 
time to 

9.30

.

on

off

Mo

Tu

We

Th

Fr

Sa

Su

3. Switch off at 19.00 hrs Mo-Fr
Using the push/turn control to select 

Mo-Fr off

 (workday group).

Hold down the SET key and use the push/turn control to set the switch off 
time to 

19.00

.

on

off

Mo

Tu

We

Th

Fr

Sa

Su

4. Switch on at 10.00 hrs Sa
Using the push/turn control to select 

Sat on

.

Hold down the SET key and use the push/turn control to set the switch on 
time to 

10.00

.

on

off

Mo

Tu

We

Th

Fr

Sa

Su

5. Switch off at 14.00 hrs Sa
Using the push/turn control to select 

Sat off

.

Hold down the SET key and use the push/turn control to set the switch off 
time to 

14.00

.

on

off

Mo

Tu

We

Th

Fr

Sa

Su

Mo

Sa

Fr

Th

We

Tu

Su

Summary of Contents for HCP 108

















































Reviews: