background image

HCP

page 15

Setting example Normal operation

Setting example Normal operation
The unit has to heat up to 50°C at a humidity of 95%rh. The monitor function has to be activated at 51°C.

1. Select operating mode “Normal operation“

1. Select operating mode “Normal operation“
After holding down the SET key (approx. 3 sec), the current operating 
mode is flashing. Select operating mode I with the push/turn control while 
holding down the SET key.
After the SET key has been released the controller is in operating mode I.

PRINT

SETUP

2. Select temperature setpoint

2. Select temperature setpoint
Hold down the SET key and use the push/turn control to select the required 
temperature setpoint of 

50.0

 °C. After the SET key has been released the 

oven briefly flashes the temperature setpoint. The display then changes to 
the actual temperature and the controller starts to control to the selected 
temperature setpoint 50,0 °C.
Heating is indicated by the orange heater symbol  .

°C

3. Select monitor temperature:

3. Select monitor temperature:
Turn the push/turn control clockwise until the overtemperature protection 
and the symbol 

MAX

 or 

MIN

 flashes. Keep the SET key depressed and 

use the push/turn control to set the overtemperature protection to 

51.0

 °C 

and the undertemperature protection to 

49.0

 °C.

or:
Turn the push/turn control clockwise until the monitor temperature and 
the symbol 

AUTO

 flashes. Keep the SET key depressed and set the push/

turn control to on .
The tolerance band is selected in the SETUP menu (see section 11).

°C

MIN

AUTO

MAX

4. Select humidity setpoint:

4. Select humidity setpoint:
High levels of air humidity in the interior can only be achieved without 
condensation if the interior is thoroughly heated. Please set the humidity 
only when the temperature in the interior has been stable for at least 30 
minutes.
Turn the push/turn control clockwise until the humidity display flashes. 
Keep the SET key depressed and use the push/turn control to set the 
required humidity setpoint of 96 %. After the SET key has been released 
the humidity setpoint continues to flash briefly. The display then changes 
to the actual humidity and the controller starts to control to the set value.
Humidification is indicated by the symbol  .

rh

%

temperature
°C

relative humidity
(rh) %

time

time

60

80

40

20

100

temperature monitor

60

80

40

20

100

Summary of Contents for HCP 108

















































Reviews: