MDT Glass Push Button II Smart BE-GT20S.01 Technical Manual Download Page 38

Page: 38 / 98

Technical Manual Glass Push Button II Smart BE-GT2xx.01

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 •

Fax: +49-2263-4588

• [email protected] • www.mdt.de

Color of message text

Any color

Setting of the color for the
message text

Indicate a message via LEDs

Yes

Setting if the LEDs should flash
at an active message

Table 13: Messages/Alarms

The message behavior depends on the parameter "Standby display at day / night". The different
behaviors are shown below:

Standby display

Incoming message during standby

no Standby

No message is displayed but saved

Standby in upper
keypad

Message is displayed on upper button pair and the upper LEDs
change between parameterized color and black at 600ms pulse

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect

The message is only acknowledged by pressing to one of the
upper buttons.

A keystroke on the middle and lower buttons performs the
displayed switching functions

Standby on full screen

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

The message is acknowledged by pressing to any key

Display off

No message is displayed during standby but saved.

The message with the highest priority is indicated by the
keystroke after standby

The displayed messages are acknowledged by means of further
key strokes

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

Display off and
orientation-LED on

Message is displayed in the middle of the screen and all LEDs
change between parameterized color and black

At the same time, the parameterized color is set to double
brightness in order to increase the signal effect.

After the "timeout for standby", the LEDs will stop flashing and
the message dispappears.

If any button is pressed after the LEDs have stopped flashing, the
message with the highest priority is displayed again. Further
keystrokes acknowledge the messages

Table 14: Behavior of the device to an incoming message during standby

Summary of Contents for Glass Push Button II Smart BE-GT20S.01



































































































Search results

Summary of Contents for Glass Push Button II Smart BE-GT20S.01

Reviews:

Related manuals for Glass Push Button II Smart BE-GT20S.01

Brands by name

Popular brands

MDT Glass Push Button II Smart BE-GT20S.01, Technical Manual

Search results

Summary of Contents for Glass Push Button II Smart BE-GT20S.01

Reviews:

Related manuals for Glass Push Button II Smart BE-GT20S.01

Brands by name

Popular brands