manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 50

 

 

APPENDIX B 

50 

AUTO-BACKUP WING PULL-TUBE 

PARTS LIST

 

Always order by Part Number - 

Not

 by Key Number 

KEY  PART # 

DESCRIPTION 

QTY. 

1 

WD-2912 

LOCK BRACKET ASSEMBLY CLAMP PLATE 

2 

2 

WD-2920  

LEFT LOCK BRACKET ASSEMBLY 

1 

** 

WD-2921 

RIGHT LOCK BRACKET ASSEMBLY 

1 

3 

WD-2922 

LOCK ARM 

2 

4 

WD-2901 

PIVOT ARM ASSEMBLY 

2 

** 

WD-2925 

PIVOT ARM ASSEMBLY, 14L TIRES 

2 

5 

WD-2904  

PIVOT ARM BASE 

2 

6 

WD-2914 

PIVOT ARM BASE CLAMP PLATE 

2 

7 

WD-2924 

AXLE CABLE GUIDE BRACKET 

4 

8 

BU-1267 

U-BOLT, 1/2 X 6 X 7 3/4 (2040-2060) 

2 

** 

BU-1278 

U-BOLT, 1/2 X 7 X 8 3/4 (2070-2080) 

2 

9 

WD-2909 

CABLE BRACKET (2040-2060)  

2 

** 

WD-2929 

CABLE BRACKET (2070-2080) 

2 

10 

HD-1216 

BUSHING 

2 

11 

HDL-2534 

EYE BOLT 

2 

12 

RBH-0308 

SPRING 

2 

13 

CH-0703 

3-LINK CHAIN 

2 

14 

AL-030 

SHACKLE 

4 

15 

WD-2911 

LOCK COLLAR 

2 

16 

WD-2915 

TUBE CONNECTOR PIN 

2 

17 

WD-2905 

WING PULL TUBE CONNECTOR 

2 

18 

CH-0607 

7-LINK CHAIN 

2 

19 

WD-181 

QUICK LINK 

2 

20 

WD-2908 

FRAME CABLE GUIDE RING 

2 

21 

WC-8105 

CABLE 

2 

22 

WD-2903 

MAIN PULL TUBE (2040) 

2 

** 

WD-2923 

MAIN PULL TUBE (2050) 

2 

** 

WD-2943 

MAIN PULL TUBE (2060) 

2 

** 

WD-2963 

MAIN PULL TUBE (2070) 

2 

** 

WD-2983 

MAIN PULL TUBE (2080) 

2 

23 

WD-2926 

WING ANCHOR LONG BUSHING 

2 

24 

WD-2906 

WING ANCHOR (2040-2060) 

2 

** 

WD-2946 

WING ANCHOR (2070-2080) 

2 

25 

WDL-2711  WING ANCHOR CLAMP PLATE (2040-2060) 

2 

** 

WDL-2731  WING ANCHOR CLAMP PLATE (2070-2080) 

2 

26 

WD-2916 

WING ANCHOR PIN 

2 

27 

WD-2936 

WING ANCHOR SHORT BUSHING 

2 

28 

WD-2918 

3/4 X 6 YOKE 

2 

29 

HD-1149 

1 X 2 1/2 CLEVIS PIN & 3/16 X 2 COTTER PIN 

2 

30 

WD-2917 

ADJUSTER ROD 

2 

 ** 

Unnumbered items are not pictured. 

 

 *** 

Please specify model number when ordering these parts. 

 

McFarlane Manufacturing reserves the right to change specifications of design at any time 
without obligation to modify previous products.

 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands