manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 14

 

14 

 

Figure 2a 

 

5.

 

Assemble either a clevis hitch (Figure 3) or a pintle hitch (Figure 4) as required by the tractor or 

towing vehicle.  Note the opposite orientation of the base hitch for each hitch type.  Attach the 

hitch assembly to the A-frame with two 1” x 6 1/2” bolts and locking nuts. 

 

Parts have been provided to assemble a clevis hitch or a pintle hitch.  Not all the included parts will 

be needed to assemble either type of hitch.  Be sure to store the extra parts in a safe place; they will 

be needed if one requires the use of the other hitch type. 

 

Note: For clarity purposes, the rest of the diagrams will be shown with out the main axles and rims.

 

 

 

 

 

3/4" x 5" BOLT

AND HEX NUT

CLEVIS

BASE

HITCH

3/4" x 2 1/2" BOLT

BASE HITCH

OR

V-PLATE

CUSHION

TOP PLATE

CLEVIS HITCH

PINTLE HITCH

 

Figure 3                                                                   Figure 4 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands