manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 48

 

 

APPENDIX B 

48 

HYDRAULIC TRANSPORT WHEEL 

PARTS LIST 

 

Always order by Part Number - 

Not

 by Key Number 

KEY  PART # 

DESCRIPTION 

QTY. 

1 

HYH-9326  3/8" x 326" HYDRAULIC HOSE (w/one ½” pipe end) 

2 

2 

WDL-2307  HYDRAULIC TEE POST 

1 

** 

BU-1278 

½” X 7” X 8 ¾” U-BOLT  

1 

3 

HYO-4000  3/8” HYDRAULIC TEE NUT 

2 

4 

HYF-1888  TEE (3/8”m – 3/8”m – 3/8”m) 

2 

5 

HYH-226 

3/8” x 226” HYDRAULIC HOSE (2040) 

2 

**

 

HYH-8285  3/8” x 285” HYDRAULIC HOSE (2050) 

2 

**

 

HYH-8345  3/8" x 345" HYDRAULIC HOSE (2060) 

2 

**

 

HYH-8400  3/8" x 400" HYDRAULIC HOSE (2070) 

2 

**

 

HYH-8460  3/8" x 460" HYDRAULIC HOSE (2080) 

2 

6 

HYF-2820  ELBOW (3/8"f – 1/2"o-ring) 

4 

7 

HYC-32004  2" x 4" HYDRAULIC CYLINDER (TIE-ROD STYLE) 

2 

 

10584 

2" x 4" HYDRAULIC CYLINDER (WELDED STYLE) 

2 

8 

HYO-2103  1" x 3 - 1/2" CLEVIS PIN 

4 

9 

HYH-8156  3/8” x 156” HYDRAULIC HOSE (2040) 

2 

**

 

HYH-8215  3/8" x 215" HYDRAULIC HOSE (2050) 

2 

**

 

HYH-8275  3/8" x 275" HYDRAULIC HOSE (2060) 

2 

**

 

HYH-8330  3/8" x 330" HYDRAULIC HOSE (2070) 

2 

**

 

HYH-8390  3/8" x 390" HYDRAULIC HOSE (2080) 

2 

10 

HYH-1004  3/8” HYDRAULIC HOSE CLAMP COVER 

4 

11 

HYH-1002  3/8” HYDRAULIC HOSE CLAMP BODY 

7 

 

** 

Unnumbered items are not pictured. 

 

 

*** 

Please specify model number when ordering these parts. 

 

 

Bolts, washers, and nuts are not shown.  Refer to the step-by-step assembly instructions for details. 

 

McFarlane Manufacturing reserves the right to change specifications of design at any time 
without obligation to modify previous products.

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands