manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 13

 

13 

STEP - BY - STEP ASSEMBLY INSTRUCTIONS 

 

Main Frame Assembly

 

 

1.

 

Bolt the square frame to the A-frame.  Refer to Figure 2.  Use sixteen 5/8” x 2” bolts, lock 

washers, and hex nuts.  Be sure to include frame cable guide ring as shown in Figure 2a. 

2.

 

Bolt the main frame axle assemblies to the frame.  Use 5/8” x 2” bolts, lock washers, and hex 

nuts.  Refer to Figure 2a to attach the axle cable guide brackets with 5/8” x 2 1/2” bolts.  Note the 

orientation of the walking axle when installing this option. 

3.

 

Mount the wheels with 11L x 15 tires on the main frame axle assemblies. 

4.

 

Attach the 10” jack to the A-frame.  Attach the hose post using the 1/2 x 8 x 5 u-bolts, lock 

washers and hex nuts. 

SQUARE FRAME

AXLE

ASSEMBLY

5/8" x 2" BOLTS, LOCK WASHERS,
AND HEX NUTS

A-FRAME

JACK

STAND

1 X 6 1/2 BOLTS AND

LOCKING NUTS

HOSE POST

 

Figure 2 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands