manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 2

 

TABLE OF CONTENTS 

 

INTRODUCTION................................................................................................................3 

LIMITED WARRANTY .....................................................................................................3 

SAFETY ..............................................................................................................................4 

CONTACT INFORMATION ..............................................................................................5 

LIGHTING AND MARKING .............................................................................................6 

SAFETY SIGN CARE.........................................................................................................7 

TIRE SAFETY ............................................................................................................... 7 - 8 

BEFORE OPERATION ................................................................................................. 7 - 8 

DURING OPERATION................................................................................................. 8 - 9 

FOLLOWING OPERATION ..............................................................................................9 

HIGHWAY AND TRANSPORT OPERATIONS ...................................................... 9 - 10 

PERFORMING MAINTENANCE ....................................................................................10 

MAINTENANCE AND SERVICE SCHEDULE .............................................................11 

OPERATING SUGGESTIONS .........................................................................................11 

ASSEMBLY SUGGESTIONS ..........................................................................................12 

ASSEMBLY INSTRUCTIONS .................................................................................13 – 37 

FINAL ADJUSTMENTS ..................................................................................................37 

TROUBLESHOOTING .....................................................................................................38 

BOLT TORQUE SPECIFICATIONS ........................................................... APPENDIX A 

PARTS DIAGRAMS AND LISTS ................................................................ APPENDIX B 

LAYOUT DIAGRAMS ................................................................................. APPENDIX C 

WARRANTY REGISTRATION FORM ........................................................ LAST PAGE 

 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands