manualshive.com logo in svg

McFarlane WDL-2000, Operator'S Manual And Set-Up Instructions

Share
Download
McFarlane WDL-2000 Operator'S Manual And Set-Up Instructions Download Page 1

 

 

MANUFACTURERS OF QUALITY AGRICULTURAL EQUIPMENT SINCE 1936 

 
 
 

OPERATOR’S MANUAL 

AND 

SET-UP INSTRUCTIONS 

FOR THE 

 
 

WDL-2000

 

REAR-FOLD TRANSPORT CART 

& HARROW SECTIONS 

 
 
 

Version: 12600 (02-17) 

Serial Number 20648 - higher 

 

TO THE OWNER AND OPERATORS 

Before assembling or operating this unit, READ THIS MANUAL THOROUGHLY.  To obtain  
the best performance of the unit, familiarize yourself with each component and adjustment.   
Store this manual where it can be readily available for future reference.  In the event that the  
harrow or any part of the unit should be sold, be sure that the new owner receives a copy of  
this manual for their reference. 
 
 

1330 Dallas Street 

∙ PO Box 100 ∙ Sauk City WI 53583 

Phone (608) 643-3321 

∙ Toll Free (800) 627-8569 ∙ Fax (608) 643-3976 

www.flexharrow.com

 

 

Summary of Contents for WDL-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands