Mazda C9F2 V6 572 EU Installation Instructions Manual Download Page 22 | Manualshive

Page: 22 / 56

background image

■

Installation instructions (For Mazda6 only)

Mazda6

－

2

DVD navigation unit removal (vehicles with navigation
system only

)

1. Remove the bolts (2 locations).

2. Disengage the navigation unit tab, and disconnect the

connector.

3. Remove the DVD navigation unit.

Connector

DVD navigation unit

Tab (1 Location)

Bolt
(2 Location)

«
...
20
21
22
23
24
...
»

Summary of Contents for C9F2 V6 572 EU

























































Reviews:

No comments

Related manuals for C9F2 V6 572 EU

Brand: Patton electronics Pages: 8

LinkStick WIS12ABGNX

Brand: Samsung Pages: 1

SmartSwitch 6C110

Brand: Cabletron Systems Pages: 7

Brand: cable matters Pages: 52

Brand: TP-Link Pages: 49

Brand: EtherCAT Pages: 74

Brand: Digitus Pages: 34

HandyPort HPU-120

Brand: HandyWave Pages: 19

Brand: Belkin Pages: 64

Brand: Skross Pages: 2

Brand: JVC Pages: 44

Brand: Bluetake Technology Pages: 30

Brand: Intellinet Pages: 2

Brand: Intellinet Pages: 30

Brand: Intellinet Pages: 34

Brand: Alcad Pages: 4

Brand: Fusion Pages: 8

Brand: Schmartz Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands