background image

 

11 

 
 
 
AVAILABLE ACCESSORIES 

 
        

WARNING:

 Use only saw blades 

that are recommended for this cordless 
jigsaw. Follow the instructions that 
accompany the saw blades. The use of 
improper saw blades may result in 
injury to the operator or damage to the 
jigsaw. 

 
Before using any accessory, carefully read 
the instructions or the owner’s manual for 
the accessory. 
 

 

U- or T-shank jigsaw blades 

 
        

WARNING:

 If any part is missing or 

damaged, do not install a battery in the 
tool until the missing or damaged part is 
replaced. 

 
CONTENTS

  

 

Carefully unpack the cordless jigsaw. 
Compare the contents against the 
“JIGSAW COMPONENTS” chart below. 

NOTE:

 See illustration of the cordless 

jigsaw and components on Page 12.  

 

 

 

 
 

 
 
 
Battery packs and chargers must be 
purchased separately.  
 
● 

This jigsaw has been designed to be 
powered by one of the following 
battery packs: 

● 

18 V Nickel-Cadmium #54-3102-2 

● 

18 V Lithium-ion #54-3100-6 

 

        

WARNING:

 Only use the battery 

packs listed above to power this tool. 
Using any other battery pack could 
cause serious injury or damage the 
tool. 

 
Both battery packs can be charged using 
one of the following chargers: 
● 

14.4 V / 18 V LED Diagnostic Battery 
Charger #54-3103-0 

● 

14.4 V / 18 V LCD Diagnostic Battery 
Charger with LCD Status Display 
#54-3101-4 

 

        

WARNING:

 Only use the battery 

chargers listed above. Charging any 
other batteries may damage the charger 
and possibly cause serious injury.

 

 

        WARNING: Follow all safety rules 
and warnings included with the battery 
pack and charger purchased for use 
with this tool. Failure to follow those 
safety rules and warnings may result in 
serious injury or damage to the charger 
and battery pack.

ACCESSORIES AND CONTENTS 

JIGSAW COMPONENTS 

KEY 

DESCRIPTION 

QTY 

Jigsaw assembly 

1/8" (3 mm) hex key 

General purpose 
blade 

 

Owner’s Manual 

 

Summary of Contents for 54-8110-2




























Reviews: