Martin VDO Face 5 User Manual Download Page 6 | Manualshive

Page: 6 / 56

background image

6

VDO Face 5™ user manual

Safety Information

The following symbols are used to identify important safety information on the product and in this manual:

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to fire hazards, electric shock and falls.

A revised version of this user manual will become available each time we can improve the quality of the
information we provide in it. Please check that you have the latest revision of the user manual for this
product before installing, operating or servicing the product. Martin® user manual revisions are identified at
the bottom of page 2. You can download the latest user documentation from the product’s Product Support
/ Tech Docs page on the Martin® website at www.martin.com.

The instructions and safety limits given in this user manual are provided to make sure that installers
comply with the

safety standards that apply to stage and studio environments

. Follow these

instructions carefully and do not exceed the limits given, or you may create an installation that is
dangerous and does not meet required safety standards. Observe all locally applicable laws,
regulations and codes regarding the safety of permanent and temporary structures, installations
and electrical systems.

Read this manual

before installing, powering, operating or servicing this product, follow the safety

precautions listed below and observe all warnings given in this manual and printed on the product.

If you have questions about how to install or operate the VDO Face 5™ system safely, please contact your
Martin supplier or call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on
1-888-tech-180.

PROTECTION FROM ELECTRIC SHOCK

• Connect the product to AC mains power within the range 100-240 V nominal at 50 or 60 Hz only.

• Disconnect the entire installation from power and ensure that power cannot be reconnected, even

accidentally, before carrying out any installation or maintenance work.

• Disconnect the product from power when not in use.

• Always ground (earth) the product electrically.

• Use only a source of power that complies with local building and electrical codes. Power distribution

circuits must be fitted with an overcurrent fuse or circuit breaker with a maximum rated current of 20 A and
ground-fault (earth-fault) protection of high breaking capacity (

≥

1500 A).

• Make power connections between VDO Face 5™ panels using only the cables supplied by Martin for this

purpose.

• Protect power connections from water and rain.

WARNING!

Read the safety precautions in this section before

installing, powering, operating or servicing VDO

Face 5™ products.

Warning!

Safety hazard.

Risk of severe

injury or death.

Warning!

Refer to

manual before

installing,

powering or

servicing.

Warning!

Hazardous

voltage. Risk of
lethal or severe

electric shock.

Warning!

Hot surface. Do

not touch.

Warning!

Fire hazard.

Warning!

Emission

hazardous to

eyesight.

«
...
4
5
6
7
8
...
»

Summary of Contents for VDO Face 5

























































Reviews:

No comments

Related manuals for VDO Face 5

Brand: NAiS Pages: 108

Brand: HANNspree Pages: 18

Brand: HANNspree Pages: 23

Brand: Hanns.G Pages: 1

SM-5000 - COMPUTER

Brand: Yaesu Pages: 8

Brand: Vitek Pages: 2

Brand: FDI Pages: 14

Brand: Gateway Pages: 30

Brand: BenQ Pages: 31

Brand: ViewSonic Pages: 2

Brand: ViewSonic Pages: 21

Brand: Hanns.G Pages: 23

Brand: NA-DE Pages: 4

Brand: Farenheit Pages: 4

Brand: DMHC Pages: 5

Brand: AOC Pages: 28

6656HG2 - T 560 - 15" LCD Monitor

Brand: IBM Pages: 34

Brand: Arestech Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands