Marantz SR3053, User Manual

Page: 22 / 31

NAMES AND
FUNCTIONS
21
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
ADV
ANCED
OPERA
TION
MANUAL PRESET MEMORY
3. 2. 4.
3.
2.
USING THE UNIT
1.
Tune into the radio station you desire (Refer
to the “ MANUAL TUNING ” or “ AUTO
TUNING ” section).
2.
Press the MEMORY button on the front
panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the
1
or
2
cursor buttons, while this is still
blinking (approx. 5 seconds)
4.
Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specifi ed
preset memory location.
USING THE REMOTE CONTROLLER
1.
Tune into the radio station you desire (Refer
to the “ MANUAL TUNING ” or “ AUTO
TUNING ” section).
2.
Press the MEMO button on the remote
controller. “– –“ (preset number) starts
blinking on the display.
3.
Enter the desired preset number by pressing
the
numeric buttons.
Note
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a
few seconds.
RECALLING A PRESET STATION
1.
1.
1.
USING THE UNIT
1.
Select the desired preset station by pressing
the
1
or
2
cursor buttons on the front
panel
USING THE REMOTE CONTROLLER
1.
Press the PRESET + or – buttons to select
the desired preset station, or input your
desired preset channel with the
numeric
buttons on the remote controller.
PRESET SCAN
3.
1.
3.
3.
USING THE REMOTE CONTROLLER
1.
Press the P.SCAN on the remote controller.
“ P-SCAN ” appears on the display and then
the preset station with the lowest preset
number is recalled fi rst.
2.
Preset stations are recalled in sequence
(No.1 → No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
ADVANCED OPERATION
3.
You can fast forward the preset stations by
pressing the continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the
CLEAR button or P.SCAN on the remote
controller.
CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
3. 2.
3.
2.
1.
Recall the preset number to be cleared
with the method described in “Recalling” a
preset station.
2.
Press the MEMORY button on the front
panel or press the MEMO button on the
remote controller.
3.
The stored preset number blinks in the
display for 5 seconds. While blinking, press
the
CLEAR button on the front panel or the
CLEAR button on the remote controller.
4.
“ xx CLEAR ” appears on the display to
indicate that the specifi ed preset number
has been cleared.
Note
To clear all stored preset stations, press and hold
the
T.MODE and the ENTER buttons on the front
panel for two seconds.
SORTING PRESET STATIONS
If you have stations memorized, and there is a gap
in the sequential order:
I.e. the stations are stored as follows
1)
87.5 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 4:
To sort the numbers, press the
4
cursor button
while pressing the MEMORY button.
“ P-SORT ” will appear on the display and sorting
will be done.
SR3053̲S̲01̲ENG.indd 21 SR3053̲S̲01̲ENG.indd 21 09.4.21 11:46:55 AM 09.4.21 11:46:55 AM