NAMES AND
FUNCTIONS
9
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
BASIC
CONNECTIONS
CONNECTING SPEAKER WIRE
1.
Strip away approx. 10 mm (3/8 inch) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent
short circuits.
3.
Loosen the knob by turning it counterclockwise.
4.
Insert the bare part of the wire into the hole
in side of each terminal.
5.
Tighten the knob by turning it clockwise to
secure the wire.
1.
2.
3.
4.
5.
10 mm
(3/8 inch)
BASIC CONNECTIONS
CONNECTING AUDIO COMPONENTS
MODEL NO. SR3053
MODEL NO. SR3053
AC IN
AC IN
FM
FM(
(75
75
Ω
Ω
)
)
GND
GND
AM
AM
ANTENNA
ANTENNA
DVD
DVD
L
L
SL
SL
C
C
R
R
L
L
R
R
L
L
SUB
SUB
WOOFER
WOOFER
R
R
SR
SR
5.1CH INPUT
5.1CH INPUT
PRE OUT
PRE OUT
SW
SW
SURROUND
SURROUND
FRONT
FRONT
MONITOR OUT
MONITOR OUT
BLU-RAY
BLU-RAY
VIDEO
VIDEO
OUT
OUT
IN
IN
L
L
R
R
Y
Y
VCR
VCR
OUT
OUT
DVD
DVD
IN
IN
BLU-RAY
BLU-RAY
VCR
VCR
DVD
DVD
BLU-RAY
BLU-RAY
IN
IN
MONITOR
MONITOR
OUT
OUT
IN
IN
DVD
DVD
BLU-RAY
BLU-RAY
OUT
OUT
REMOTE
REMOTE
CONTROL
CONTROL
ANALOG AUDIO
ANALOG AUDIO
DIGITAL AUDIO IN
DIGITAL AUDIO IN
IN
IN
COMPONENT VIDEO
COMPONENT VIDEO
MONITOR
MONITOR
OUT
OUT
P
P
B
B
C
C
B
B
P
P
R
R
C
C
R
R
SPEAKER SYSTEMS : 6-8 OHMS
SPEAKER SYSTEMS : 6-8 OHMS
CENTER
CENTER
BLU-RAY
BLU-RAY
CD
CD
COAXIAL
COAXIAL
OPTICAL
OPTICAL
DVD
DVD
CD
CD // TAPE
TAPE
IN
IN
L
L
R
R
OPTICAL
OPTICAL
ANALOG AUDIO
ANALOG AUDIO
DIGITAL AUDIO IN
DIGITAL AUDIO IN
CD
CD
CD
CD // TAPE
TAPE
OUT
L
R
L R
R L
DIGITAL
OUTPUT
L
R
CD Player
Analog Audio
Digital Audio (optical)
When using a tape deck, connect Analog Audio OUT/IN only.
Notes
• Do not connect this unit and other components to mains power until all connections between components have
been completed.
• Insert all plugs and connectors securely. Incomplete connections may make noise.
• Be sure to connect the left and right channels properly.
Red connectors are for the R (right) channel, and white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is connected to this unit.
• Do not tie the connected cable into a bundle with the power supply cord or speaker cables. Doing so may cause
noise.
CONNECTING DIGITAL AUDIO
COMPONENTS
• There are 3 digital inputs, 2 coaxial jacks and
1 optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a Blu-ray, DVD, and CD.
• Refer to the instructions for each component. To
setup the digital audio format of Blu-ray player, or
other digital source’s connected to digital input
jacks.
• Use fi ber optical cables (optical) for CD, input
jacks. Use 75 ohms coaxial cables (for digital
audio) for Blu-ray, DVD, input jacks.
Notes
• There is no Dolby Digital RF input jack. Please
use an external RF demodulator Dolby Digital
decoder when connecting the Dolby Digital RF
output jack of the video disc player to the digital
input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does
not conform to this standard, this unit may not
function properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks
are output through the corresponding digital and
analog jacks, respectively.
SR3053̲S̲01̲ENG.indd 9
SR3053̲S̲01̲ENG.indd 9
09.4.21 11:46:51 AM
09.4.21 11:46:51 AM
