NAMES AND
FUNCTIONS
13
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
BASIC
OPERA
TION
BASIC OPERATION
• When an audio source is selected, the last video
input used remains routed to the
VCR
Output
and
Monitor
Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the
Monitor
Output
jacks and will be viewable on a TV
monitor connected to the unit.
If a component video input is connected to the
DVD
or
BLU-RAY
component inputs, it will be
routed to the
Component Video Output
. Make
certain that your TV is set to the proper input to
view the signal.
ADJUSTING THE MAIN VOLUME
Adjust the volume to a comfortable level using
the
VOLUME
control knob on the front panel or
VOLUME
+
/
–
buttons on the remote controller.
To increase the volume, turn the
VOLUME
knob
clockwise or press
VOLUME
+
button on the
remote controller, to decrease the volume, turn
counterclockwise or press
VOLUME
–
button on
the remote controller.
Notes
• The volume can be adjusted within the range of
VOL MUTE – to 16 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 17, if the volume for any channel is set at
+1 dB or greater, the volume cannot be adjusted
up to 16 dB.
(In this case the maximum volume adjustment
range is “16 dB - Maximum value of channel
level)
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
During a listening session you may wish to adjust
the Bass and Treble Control to suit your listening
tastes or room acoustics.
USING THE REMOTE CONTROLLER
To adjust the bass effect, press
BASS +
or
BASS
–
on the remote controller.
To adjust the treble effect, press
or
TREBLE –
on the remote controller.
Note
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLII and DTS mode.
TEMPORARILY TURNING OFF THE SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the
MUTE
button on the remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“
MUTE
” .
Press the
MUTE
button again to return to normal
operation.
TUNER OPERATION
Frequency scan step for AM is selectable.
Default setup is 9 kHz step, if your country’s
standard is 10 kHz step, Press
BAND
button on the
remote controller more than 6 seconds. Scan step
will change.
Note
Preset memory for the tuner will clear by changing
this setup.
AUTO TUNING
2.
1.
2.
1.
USING THE UNIT
1.
To select tuner and desired band (FM or
AM), press the
BAND
button on the front
panel.
2.
Press
the
3
or
4
cursor buttons on the front
panel for more than 1 second to start the
auto tuning function.
3.
Automatic searching begins then stops
when a station is tuned in.
USING THE REMOTE CONTROLLER
1.
To select tuner and desired band (FM or
AM), press the
BAND
button on the remote
controller.
2.
Press
the
TUNE
3
or
4
for more than 1
second on the remote controller.
3.
Automatic searching begins then stops
when a station is tuned in.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
MANUAL TUNING
2.
1.
2.
1.
USING THE UNIT
1.
To select tuner and desired band (FM or
AM), press the
BAND
button on the front
panel.
2.
Press
the
3
or
4
cursor buttons on the front
panel to select the desired station.
USING THE REMOTE CONTROLLER
1.
To select tuner and desired band (FM or
AM), press the
BAND
button on the remote
controller.
2.
Press the TUNE
3
or
4
on the remote
controller to tune in the desired station.
(FM) TUNING MODE (AUTO STEREO OR MONO)
The “
ST
” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“
TUNED
” and “
ST
” indicators are not illuminated.
If the signal is weak, it may be diffi cult to tune into
the station in stereo. In such a case, press the
T.MODE
button on the front panel or remote
controller.
The “ST” indicator is not illuminated, if FM stereo
broadcasts are received in monaural.
To return to auto stereo mode, press the
T.MODE
button or press
T.MODE
button on the remote
controller again.
SR3053̲S̲01̲ENG.indd 13
SR3053̲S̲01̲ENG.indd 13
09.4.21 11:46:52 AM
09.4.21 11:46:52 AM
