background image

 

 

 

AVS S-Series – AVS S3/S4/S5 

Installation  manual 

 

Generation 2 Version 5 

Serials: 6401513 – Current 

Make sure you are using the correct manual 

 

AVS S3 

 

Certification: 

 

Test report XF2070/R1

 

 

The AVS S3 is certified to AS/NZS 4601:1999 Amendment A 2003

 

 

 

 

AVS S4 

 

Certification: 

 

Test Report XF2106/R2 

 

This  product  complies  with  AS/NZS  3749.1  2003 Class B. Volumetric Sensing (glass break/shock) must remain disabled to 
comply with a Class B installation (refer Programmable Features). 

 

Class  B  VSAS  (Vehicle  security  alarm  system)  includes  control  equipment  including  setting  and  unsetting  facilities,  all 
sensors, warning devices and provisions for immobilization of the vehicle 

 

 

 

 

AVS S5 

 

Certification: 

 

Test Report XF2106/R2 

 

This  product  complies  with  AS/NZS  3749.1  2003  Class  A.  Volumetric  Sensing  (glass  break/shock)  must  be  enabled  to 
comply with a Class A installation (refer Programmable Features). 

 

Class  A  VSAS  (Vehicle  security  alarm  system)  includes  control  equipment  including  setting  and  unsetting  facilities,  all 
sensors,  warning  devices  and  provisions  for  immobilization  of  the  vehicle  and  the  volumetric  sensing  device  (glass 
break/shock) 

 

 

 
 

Manta help line 09 476 8052 

 

AVS is a registered trademark of the 

group of companies 

Summary of Contents for AVS S Series





































Reviews: