Mannesmann Rexroth Indramat ECODRIVE DKC01.1 Project Planning Manual Download Page 57

Page: 57 / 108

ECODRIVE DKC01.1/DKC11.1 Drive Controllers

BZM auxiliary bleeder module

5-1

DOK-ECODRV-DKC01/11.1*-PRJ3-EN-P

BZM auxiliary bleeder module

5.1

Dimensioning the components relevant for regeneration

For each servo-technical application, it is necessary to check whether the

•

continuous regenerative power

•

peak regenerative power

•

regenerative energy

needed for the application can be sufficiently absorbed by the bleeder
(brake resistance).

If the available regenerative power and energy from the mechanics ex-
ceeds the absorbing capabilities of the bleeder built into the unit, this ca-
pability can be increased on the DKC**.*-040-7-FW by using the following
hardware configurations.

•

A drive and auxiliary bleeder module connected via the DC bus circuit.
(1 DKC+BZM)

•

Several drive controllers connected via the DC bus circuit. (up to 6
DKCs)

•

Several drive controllers and auxiliary bleeder modules connected via
the DC bus circuit. (up to 6 DKC+BZM)

Buy: www.ValinOnline.com | Phone: 844-385-3099 | Email: [email protected]

Summary of Contents for Indramat ECODRIVE DKC01.1













































































































Search results

Summary of Contents for Indramat ECODRIVE DKC01.1

Reviews:

Related manuals for Indramat ECODRIVE DKC01.1

Brands by name

Popular brands

Mannesmann Rexroth Indramat ECODRIVE DKC01.1, Project Planning Manual

Search results

Summary of Contents for Indramat ECODRIVE DKC01.1

Reviews:

Related manuals for Indramat ECODRIVE DKC01.1

Brands by name

Popular brands