manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 64 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 64

63

10/07

- Before installing a new bearing, heat
the flywheel side half-crankcase using
the special tool.

- Place the half-crankcase on a wooden
base.

Specific tooling

020151Y
Air heater

- Fit the seeger ring.

- Before installing the new bearing on
the transmission side crankcase, heat
the seat using the special tool.

Specific tooling

020151Y
Air heater

- Insert a new bearing on the special
tool after greasing the guide seat.

- Install the new bearing on the half-
crankcase using the special tool.

N.B.
IF A BEARING WITH PLASTIC CAGE IS
USED, KEEP THE BALLS VISIBLE FROM
THE CRANKCASE INTERNAL SIDE.

Specific tooling

020376Y
Adaptor handle
020359Y
42 x 47 mm adaptor
020439Y
17 mm guide

Specific tooling

020376Y
Adaptor handle
020359Y
42 x 47 mm adaptor
020439Y
17 mm guide

- Insert a new bearing on the special
tool after greasing the guide seat.
- Install the new bearing on the engine
crankcase using the special tool.

N.B.
IF A BEARING WITH PLASTIC CAGE IS
USED, KEEP THE BALLS VISIBLE FROM
THE CRANKCASE INTERNAL SIDE.

Summary of Contents for 500 cc 4T















































































Reviews:

No comments