manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 18 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 18

17

10/07

Refitting the driven pulley

- Install the driven pulley assembly with
belt.

Drive-belt

- Check that the driving belt is not
damaged.

- Check the width of the belt.

Characteristic

Minimum width
27.5 mm
Overall width
28.7 mm

Removing the driving
pulley

- Using a 27 mm wrench, turn the
central pulley nut to horizontally align
the central inside holes and install the
special tool.

Specific tooling

020474Y
Driving pulley lock wrench

- First fit the 2 retainer clamps of the
special tool onto the pulley so that the
splines are completely engaged.

- Then, insert the tool so as to insert
the stud bolts on the ring into the holes
obtained onto the tool itself.

- Tighten the two tool fixing screws,
also manually.

- Loosen the central nut.

- Remove the spring washer and the flat
washer.

- Remove the fixed driving half-pulley.

- Remove the bushing connection
washer.

- Move the belt downwards.

- Suitable support the roller contrast
and extract the mobile driving half-pulley
with the relevant bushing and the rear
washer, being careful not to make the
rollers come out.

- Measure the pulley sliding bushing
outside diameter shown in the figure.

Summary of Contents for 500 cc 4T















































































Reviews:

No comments