manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 21 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 21

20

10/07

- Install the lock ring from the rear so that
the splines are completely engaged.

- Finally install the tool by siding the
nuts by hand and ensuring the tool is
resting flatly.

- Tighten the driving pulley fastening nut
to the prescribed torque

- Remove the special tool.

Refitting the transmission
cover

- Ensure the correct installation on the
crankcase of the 2 centring dowels.

- Insert the transmission cover with the
bearing and install the relevant
retainers.

- Lock the four M8 retainers.

- Lock the 7 M6 retainers.

- Insert the washers on the driven pulley
shaft.

N.B.
INSERT THE SMALLER WASHER FIRST,
THEN THE LARGER ONE.

- Insert the flanged nut.

- Prepare the torque wrench for LHS
locking hexagon wrench.

- Tighten the driven pulley shaft
fastening nut using an offset wrench.

N.B.
DUE TO THE HIGH TIGHTENING TORQUE, USING DIFFERENT WRENCHES - SUCH AS A
CONVENTIONAL POLYGONAL BUSH - MAY DAMAGE THE HEXAGON OBTAINED ON THE
SHAFT OR BREAK THE BUSH ITSELF.

Locking torque (N*m)

Drive pulley nut
160 - 175

Locking torques (N*m)

M8 retainers for transmission cover
23 - 26

Locking torque (N*m)

Driven pulley nut
92 - 100

Locking torques (N*m)

M6 retainer
11 ÷ 13

Summary of Contents for 500 cc 4T















































































Reviews:

No comments