manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 22 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 22

21

10/07

- Install the driving pulley shaft cover,
positioning the tooth gap on the lower
part with the reference mark on the
transmission crankcase.

N.B.
ENSURE THAT THE AIR INTAKE AND
EXHAUST OPENINGS ARE COMPLETELY
FREE.

- Install the outside plastic transmission
cover.

- Tighten the 4 fastening screws to the
prescribed torque.

End gear

Removing the hub cover

- Drain the rear hub oil through the oil
drainage cap located under the engine.

-Remove the 7 fastening screws.
Remove the hub cover and the relevant
gasket.

Removing the wheel axle

- Remove the countershaft.

- Remove the wheel axis complete with
gear.

Removing the hub
bearings

- Check all bearings (wear, clearance
and noise).

In case of anomalies, proceed as
follows.

To remove the gear shaft bearing on the
engine crankcase, use the following
parts.

Specific tooling

001467Y014
Extraction pliers for ø 15 mm bearings
001467Y034
Extraction pliers for ø 15 mm bearings
001467Y031
Bell

Locking torques (N*m)

Outside transmission cover screws
7 ÷ 9

Summary of Contents for 500 cc 4T















































































Reviews:

No comments