manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 52 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 52

51

10/07

Specification 

Desc./Quantity 

Inlet: 

95.0 ± 0.3 mm 

Outlet: 

94.2 ± 0.3 mm 

Specification 

Desc./Quantity 

Standard clearance: 

0.025 ÷ 0.052 mm 

Admissible limit: 

0.09 mm 

Specification 

Desc./Quantity 

Standard clearance: 

0.013 - 0.04 mm 

Admissible limit: 

0.08 mm 

Specification 

Desc./Quantity 

Inlet: 

4.96 mm 

Outlet: 

4.945 mm 

Specification 

Desc./Quantity 

Inlet: 

4.987 - 4.972 mm 

Outlet: 

4.975 - 4.960 mm 

Inspecting the valves

- Measure the diameter of the valve stems in the three positions indicated in the
diagram.

- Calculate the clearance between valve
and valve guide.

- Check the deviation of the valve stem by
resting it on a "V" shaped abutment and
measuring the extent of the deformation by
a comparator.

Characteristic

Limit values admitted:
0.01 mm

Inspecting the valve stem guide clearance

- After measuring the valve guide diameter and the valve stem diameter, check the
clearance between guide and stem.

- Check that there are no signs of wear on the surface of contact with the articulated
register terminal.

STANDARD DIAMETER

MINIMUM ADMISSIBLE DIAMETER

STANDARD VALVE LENGTH

OUTLET

INLET

- Check the concentricity of the valve head
by arranging a comparator at right angle
relative to the valve head and rotate it on a
"V" shaped abutment.

Characteristic

Admissible limit:
0.03 mm

Summary of Contents for 500 cc 4T















































































Reviews:

No comments