manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 25 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 25

24

10/07

Refitting the driven pulley
shaft bearing

- Heat the crankcase using the heat
gun.

Specific tooling

020151Y
Air heater

- Insert the driven pulley shaft bearing
until it abuts against the bottom of the
seat using the special tool.

N.B.
PLACE IT WITH THE BALLS FACING THE
HUB (THIS APPLIES TO BEARINGS WITH
PLASTIC CAGE).

Specific tooling

020376Y
Adaptor handle
020360Y
52 x 55 mm adaptor
020364Y
25 mm guide

- Heat the intermediate gear bearing
seat.

- Insert the intermediate shaft bearing
using the special tool.

N.B.
PLACE IT WITH THE BALLS FACING THE
HUB (THIS APPLIES TO BEARINGS WITH
PLASTIC CAGE).

Specific tooling

020376Y
Adaptor handle
020359Y
42 x 47 mm adaptor
020363Y
20 mm guide

- Heat the gear shaft bearing seat on
the crankcase.

- Insert the gear shaft bearing in the upper
crankcase seat using the special tool.

N.B.
PLACE IT WITH THE BALLS FACING THE
HUB (THIS APPLIES TO BEARINGS WITH
PLASTIC CAGE).

Specific tooling

020376Y
Adaptor handle
020359Y
42 x 47 mm adaptor
020412Y
15 mm guide

Summary of Contents for 500 cc 4T















































































Reviews:

No comments