manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 38 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 38

37

10/07

Intermediate gear

- Check that the toothing is not worn.
- Check the diameter of the two
bearings.

Characteristic

Diameter of gear bearing:
12           mm

Refitting the free wheel

- Make sure the free wheel contact surfaces are in good condition.
- Thoroughly clean the free wheel to remove LOCTITE residue.
- Degrease the threading of the holes in the free wheel and the clamping screws.
- Apply the recommended product to the end of the screws.

Recommended products

Loctite 243
Medium strength threadlock
Medium Loctite 243 threadlock

- Fit the freewheel on the magneto
flywheel making sure that the ground
side is in contact with the flywheel
itself, i.e. with wheel Seeger ring visible.

- Lock the six clamping screws in criss-
cross fashion to the prescribed torque.

Locking torques (N*m)

Screw fixing freewheel to flywheel
13 - 15

- Oil the free wheel "rollers".

Also check the shaft diameter on the
flywheel cover and on the engine
crankcase.

Characteristic

Shaft diameter on the flywheel cover
12           mm

Shaft diameter on the engine
crankcase:
12           mm

N.B.
THE TORQUE LIMITER IS PROVIDED WITH
4 GEARS THAT HAVE THE FUNCTION OF
CLUTCH DRIVE PLATES.

Driven plates consist of 4 Belleville
springs provided with grooved profiles;
this assembly allows transmitting
torque lower than 10 kgm.

In case of incorrect start-up
manoeuvres, the limiter prevents any
kicks, with consequent reversal of
direction of the crankshaft which would
impair the engine structure.
The limiter assembly cannot be
overhauled. In case of irregularities on
the toothed discs, replace the
assembly.

-0
-0,011

+0,034
-0,016

+0,034
-0,016

Summary of Contents for 500 cc 4T















































































Reviews:

No comments