manualshive.com logo in svg

Malaguti 500 cc 4T, Service Manual, Page: 40 / 78

Share
Download
Malaguti 500 cc 4T Service Manual Download Page 40

39

10/07

- Tighten thoroughly the guide bushing
of the flywheel lock tool and loosen by
1/4 turn.

N.B.
FAILURE TO OBSERVE THIS RULE
CAUSES THE LOCKING OF THE GUIDE ON
THE FLYWHEEL.

Specific tooling

020472Y
Flywheel lock wrench

- Align the 2 holes of the flywheel with
the case housing to allow the
introduction of the special tool.

- Insert the special tool checking that
the pins are perfectly introduced into
the seat.

Specific tooling

020472Y
Flywheel lock wrench

- Tighten the flywheel lock nut to the
prescribed torque.

Locking torques (N*m)

Flywheel fixing nut
115 - 125

- Install the chain guide retain plate
tightening the 3 screws to the
prescribed torque.

N.B.
BEFORE TIGHTENING THE SCREWS,
MOVE THE START-UP RIM IN CONTACT
WITH THE CRANKCASE AND CHECK THAT
IT IS FREE TO ROTATE IN
ANTICLOCKWISE DIRECTION.

Locking torques (N*m)

Chain guide sliding block retain
plate fastening screws
3 ÷ 4

Refitting the starter motor

- Check that the O-ring is in good
working order and lubricate it.

- Insert the starter motor.

- Tighten the 2 fastening screws to the
prescribed torque.

Locking torques (N*m)

Starter screws
11 ÷ 13

Summary of Contents for 500 cc 4T















































































Reviews:

No comments