background image

P 5/ 24

R

epair

[4] DISASSEMBLY/ ASSEMBLY

[4]-1. Magazine section

DISASSEMBLING

(1) Remove Magazine section, and then separate Slide door from Magazine. (

Fig. 3

)

Fig. 3

Fig. 3

Fig. 3

M4x12 Pan head screw

(2 pcs.)

Magazine

section

Driver guide section

Magazine

section

Magazine

M5x20 Hex socket head bolt

(2 pcs./ Thread-locker type)

[7.5-9.0 N·m]

M4x8 Hex socket 

head bolt (2 pcs.)

[2.7-4.2 N·m]

M4x6 Hex socket

head bolt

M4x6 Hex socket head bolt (2 pcs.)

[2.7-4.2 N·m]

Plate A

Nail plate

Magazine

Center plate complete

Set plate

Set plate

Plastic hammer

Compression spring 4

Driver guide

M4x10 Hex socket head bolt

Slide door

Slide door

1. Remove two M4x12 Pan head screws.

3. Remove Magazine section.

5. Remove an module (Driver guide, Center plate 

    complete and Compression spring 4) from Set plate. 

2. Remove M4x6 Hex socket head bolt and two M5x20 Hex socket head 

    bolts (Thread-locker type). Then, disassemble Driver guide section.

4. Remove two M4x6 Hex socket head bolts and Plate A.

6. Remove two M4x8 Hex socket head bolts and separate 

    Set plate from Magazine.

Note

: The fitting between Set plate and Magazine is tight, 

          and therefore, tap Set plate with a plastic hammer.

7. Remove Nail plate from Magazine section.

8. Remove M4x10 Hex socket head bolt, and then 

     pull out Slide door from Magazine.

Summary of Contents for DBN500

























Reviews: